ESP8266 ESP-01 WiFi 12V 1x Rele
€8.99 (DDV vključen)
Optimizirajte svoje projekte z ESP8266 ESP-01 WiFi 12V 1x Rele. Zanesljivo krmiljenje, idealno za Arduino, ESP32 in pametni dom. Preverite specifikacije in PRO
3 na zalogi
Opis
ESP8266 ESP-01 WiFi 12V 1x Rele
Brezžični nadzor preko WiFi omrežja
The ESP8266 ESP-01 WiFi 12V 1x Relay module provides a straightforward method to integrate any consumer device (lights, fans, sockets, chargers) into a smart home or DIY automation project. It combines an ESP-01 WiFi module, an STM8S microcontroller for local logic, and a 12V relay with isolated COM/NO/NC contacts on a single board. The STM8S microcontroller manages the ESP-01, LED indicators, and operating modes, allowing users to focus on application rather than low-level WiFi module initialization.
UART (TX/RX) pins are available for reprogramming the ESP-01 or integrating it into custom systems. The module is suitable for beginners, students, and advanced hobbyists looking to quickly implement WiFi control without designing power supply and protection circuits. Power is supplied via IN+/IN- terminals, and the load is connected to the relay terminals.
The module connects to a WiFi network using a dedicated mobile application. Use cases include remote switching of lights or LED strips, controlling fans, pumps, or small motors, managing heating systems, creating simple WiFi switches for workshops or garages, and integrating into DIY controllers (Arduino, ESP32, Raspberry Pi) as a WiFi-controlled relay output. The module is compatible with most existing ESP-01 firmware solutions and typical mobile applications for WiFi switches using TCP communication.
The ESP-01 can be reprogrammed with custom firmware (e.g., ESP-Easy, Tasmota, custom Arduino sketch) via UART..
Ključne lastnosti
- Združljivost z Arduino, ESP32 in drugimi krmilniki
- Napredna komunikacija (WiFi/Bluetooth)
- Vgrajena zaščita in galvanska ločitev
Tehnične specifikacije
| Parameter | Podatek |
|---|---|
| WiFi Chip | ESP8266 ESP-01 |
| Auxiliary Microcontroller | STM8S |
| Power Supply | 12V DC (some versions may support 5V; check markings) |
| Relay Type | Typical SRD-12VDC-SL-C or compatible |
| Rated Relay Contacts | Up to 10A / 250VAC or 10A / 30VDC (check relay markings) |
| Relay Connections | COM, NO, NC (screw terminals) |
| Logic Interface | UART (TX, RX) for ESP-01 |
| STM8S Programming Interface | SWIM, NRST, 5V/12V, GND |
| Indicators | LED D2, D4, D5, D6, D7 |
| Control Buttons | S1 (mode change), S2 (factory reset) |
| Board Dimensions | Approximately 58 mm × 29 mm |
| Integrated ESP8266 ESP-01 WiFi module for wireless control | |
| On-board STM8S microcontroller for logic and communication with ESP-01 | |
| 12V relay with separate COM / NO / NC contacts for load control | |
| Power supply via IN+ / IN- terminals with 12V DC | |
| Separate UART (TX, RX) port for serial communication or custom ESP-01 programming | |
| Programming port 5V / 12V, GND, SWIM, NRST for STM8S firmware upload | |
| S1 button for changing operating mode (default Mode 1) | |
| S2 button for factory reset | |
| LED D2 and D4 (red) as relay operation indicator (lit when relay is on) | |
| LED D7 (red) as Mode 1 indicator | |
| LED D5 (blue) as Mode 2 indicator | |
| LED D6 (green) as WiFi / connection indicator | |
| Off | Module self-configuring or no router connection |
| Fast blinking (approx. 0.5s) | Waiting for app to set WiFi SSID and password |
| Slow blinking (approx. 2s) | WiFi configuration complete, waiting for TCP connection with phone |
| Solid | Successful TCP connection with phone |
| Two reserved jumpers for switching connection between ESP-01 and STM8S or USB-TTL adapter | |
| Lower position | RX → RX1, TX → TX1 (normal module operation) |
| Upper position | For ESP-01 debugging via external USB-TTL interface (to avoid STM8S interference) |
| Tested relay commands in hex format for serial control | |
| Toggle relay | A0 01 01 A2 |
| Turn off relay | A0 01 00 A1 |
Inženirski “PRO” nasvet
For WiFi relay modules like this, power supply and grounding are critical. Ensure the 12V power source is sufficiently powerful and reliable, and crucially, that the GND is common between the power supply, ESP-01, and other electronics. If using a USB-TTL adapter for ESP-01 programming, move the jumpers to the upper position during testing to avoid interference from the STM8S. When controlling 230V mains voltage, always observe safety distances, ensure proper insulation, and use additional enclosures or fuses if necessary.
Primeri uporabe
- Pametni dom in IoT avtomatizacija
- Daljinsko upravljanje naprav preko telefona
- Razširitev I/O pinov pri kompleksnih projektih
Dodatne podrobnosti
| ESP8266 | z ESP8266, brez ESP8266 |
|---|
